PPP REFERENCE: Improving Kiln Uniformity

The most reliable way to check heat distribution in your kiln is to use a series of witness cones on each shelf. (Photo courtesy of Jeff Zamek.)

Temperature distribution in a kiln can be affected by many different factors, including:
  • the design of the kiln
  • firing temperature
  • the load in the kiln
  • the rate of heating
  • the use of an automatic vent system
  • how the kiln switches are adjusted
  • if a hold (soak) is used
  • the age and condition of the heating elements and kiln
Throughout the firing, hot air rises and cool air falls. As a result, some kilns will fire cooler at the bottom than the top. Today's redesigned kilns generally provide improved uniformity, but it is not uncommon to see a full cone difference from top to bottom in the kiln, or a half-cone difference on a single shelf in a large kiln.

How Heat Moves

In the early stages of firing, warmed air circulates through the kiln. Later, the hot kiln elements radiate direct heat onto the ware. Hot air moves through the ware, transferring heat by convection to the ware. Then it is conducted to the inside of the ware.

Firing Temperatures

At higher temperatures, most of the heat is transferred by radiation from hot elements or hot gas. Kilns fired to lower cone numbers tend to be less uniform than kilns fired to higher temperatures (016 vs. 6). This is because radiation is more effective in transferring heat.

Load Makes a Difference

With a heavy load, it is more difficult to evenly distribute heat through the kiln. When a kiln has a moderate-to-light load, low heat can better circulate and radiant heat can reach more of the ware to reduce hot and cold spots.

Kiln Characteristics

How big is the kiln?
For larger kilns, there is more space (and usually more ware) to heat. It takes longer for heat to be transferred. It is not unusual to see even a two-cone difference (top to bottom) in a large kiln. While kiln manufacturers help compensate for this problem, it is not cost effective to fully eliminate top-to-bottom differences.

What is the element condition?
Aging elements in one part of the kiln will affect heat distribution in that section. At full heat, all of the elements should glow red. Elements that do not are likely aging and should be replaced. Check your kiln manual. Some kiln manufacturers recommend replacing all of the elements at the same time for best results.

Controlling the Firing

One of the easiest ways to improve uniformity is to adjust the switch settings on the kiln to send more heat to cooler areas. As an example, for a kiln that is cooler at the bottom, turn the bottom switches on earlier than the other switches, or turn them on higher than the others. This allows the bottom to heat up more/faster than the rest of the kiln so it doesn't have to catch up later.

If an automatic controller is used, the firing rate can be slowed to permit the heat to distribute throughout the kiln. Setting a hold time just below the top temperature is a good way to reduce temperature distribution problems and to help ware mature more evenly.

Kiln Venting Systems

Downdraft kiln venting systems help solve temperature uniformity problems. A small amount of air is pulled in the top of the kiln, circulated throughout the firing chamber and exhausted out the bottom of the kiln. As the hot air moves through the firing chamber, it evens out temperatures (often by as much as two cone numbers).

Checking Uniformity

The most reliable way to check heat distribution in your kiln is to use a series of witness cones on each shelf. By examining them after each firing, you can see how firing conditions, including uniformity, affect fired results. Adjustments in switching, loading, etc. can be evaluated for their effect on heat distribution.

Editor's note: This information has been provided by The Edward Orton Jr. Ceramic Foundation. For additional information, visit www.ortonceramic.com.


Did you enjoy this article? Click here to subscribe to Ceramic Industry Magazine.

You must login or register in order to post a comment.



Image Galleries

2015 Ceramics Expo

Snapshots from the 2015 Ceramics Expo, April 28-30, Cleveland, Ohio. Posted: May 14, 2015.


Ceramics Expo podcast
Editor Susan Sutton discusses the upcoming Ceramics Expo with event director Adam Moore.
More Podcasts

Ceramic Industry Magazine

CI May 2015 cover

2015 May

Our May issue covers bulk batching, pneumatic conveyors, high-temperature furnaces and more! Be sure to check it out today.

Table Of Contents Subscribe

Daily News

We know where you find the latest ceramic industry news (ahem), but where do you catch up on the rest of your daily news?
View Results Poll Archive


M:\General Shared\__AEC Store Katie Z\AEC Store\Images\Ceramics Industry\handbook of advanced ceramics.gif
Handbook of Advanced Ceramics Machining

Ceramics, with their unique properties and diverse applications, hold the potential to revolutionize many industries, including automotive and semiconductors.

More Products

Clear Seas Research

Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.


facebook_40px twitter_40px  youtube_40pxlinkedin_40google+ icon 40px


CI Data Book July 2012

Ceramic Industry's Directories including Components, Equipment Digest, Services, Data Book & Buyers Guide, Materials Handbook and much more!