- THE MAGAZINE
- Advertiser Index
- Raw & Manufactured Materials Overview
- Classifieds & Services Marketplace
- Product & Literature Showcases
- List Rental
- Market Trends
- Material Properties Charts
- Custom Content & Marketing Services
- CI Top 10 Advanced Ceramic Manufacturers
- Virtual Supplier Brochures
It is difficult to believe that the microwave ovens we use to heat soup and bake potatoes can get hot enough to fuse or melt glass. In reality, not only can microwave ovens fuse glass, but most ovens can do it in less than 10 minutes.
I first began experimenting with microwave firing last year to make glass-fused pendants. I used the microwave oven in the Paragon employee kitchen for most of the firings, and I also used two smaller and inexpensive microwaves to compare the results I was getting with the larger microwave.
Microwave BasicsMaking glass jewelry is fun and will teach you the principles of glass fusing. With practice, you should be able to achieve consistent results in microwave firing. You will need a microwave kiln, which is a small ceramic fiber container that fits inside the microwave oven. The microwave kiln captures microwave energy and concentrates it in the firing chamber. The concept is similar to using a magnifying glass to focus sunlight.
The biggest challenge to microwave firing is the fast heating rate. A microwave kiln reaches 1650°F (899°C) in only 5-10 minutes. Firing times depend on the wattage of the microwave oven; the lower the wattage, the longer the firing time. However, firings can be controlled to achieve consistent results.
Only small glass projects can withstand rapid heating. The glass should be no larger than 1 x 1½ in. and no thicker than two layers of 1/8-in. stained glass. The glass must be clean; even a greasy fingerprint can cause the glass to break apart during the initial heating.
Getting StartedThough these instructions are basic, more detailed information will be included in your microwave kiln manual. Fire only fusing-compatible stained glass, or the pieces will break due to differences in their coefficients of expansion. Your stained glass supplier can show you how to cut the glass. Required supplies include a microwave oven and kiln, kiln wash and a small paintbrush, clear firing safety glasses, heat-protective gloves, six ½-in. kiln posts, a 12 x 12-in. kiln shelf or other heat-proof surface, and a glass cutter.
First, protect the base of the kiln by applying a coating of kiln wash or glass separator with a small paintbrush. The coating prevents the glass from sticking to the kiln base. After the coating is completely dry, place the glass pieces on the base.
Lay the 12 x 12-in. ceramic shelf or other heat-proof surface near the microwave oven. Arrange three ½-in. ceramic posts on the shelf. When the glass has fused, you will remove the kiln from the microwave and place the kiln on the three posts.
Position the glass pieces on the kiln base. For your first firing, load only one test piece. (Later, you can try firing three or more pieces per load.) Place the kiln bottom and glass on top of three ½-in. posts inside the microwave. You can place the posts on the rotator tray or directly on the bottom of the oven if you’ve removed the rotator tray. Gently position the kiln over the kiln base and close the microwave oven door. The loading process is shown in Figure 1. You are ready to fire the glass.
While it is okay to fire small pieces at full power, starting with 50% power for five minutes increases the success rate, especially with larger pieces. The glass is less likely to break with a pre-heat. See your microwave manual for instructions on reduced power settings. (You can probably find the instructions on the Internet if you don’t have the manual.)
As you gain experience, you will sense just when to start visually checking the glass. I check every 20 seconds toward the end of a firing because I want to stop the firing at a precise stage of fusing, usually between tack fuse and medium fuse.
Fusing FunOnce you learn how to achieve good results consistently, you will be amazed at what you can make. I gave a glass-fused pendant to my 13-year-old niece and she liked it so much that she even wore it while she slept.
I learn something new every time I fire a microwave kiln. You can experiment endlessly with designs and colors. I used hairspray as an adhesive once, and the spray produced a beautiful silvery sheen over dichroic glass. You will make many such serendipitous discoveries with microwave glass fusing.
For additional information regarding glass fusing, contact Paragon Industries, L.P. at 2011 South Town East Blvd., Mesquite, TX 75149; (972) 288-7557; fax (972) 222-0646; e-mail email@example.com; or visit www.paragonweb.com.
Author's NotePlease follow the safety rules in your kiln manual, and always wear clear safety glasses when looking at the hot glass.
SIDEBAR: Microwave Kiln Safety
- Wear clear safety glasses whenever visually checking hot glass, and stay at arm’s length.
- Fire only fusing-compatible glass in a microwave kiln.
- Wear heat-protective gloves when removing the hot kiln from the oven.
- Remove the kiln from the oven immediately after the firing is completed to avoid over-heating the oven.
- Separate the hot kiln from the heatproof surface with three ½-in. ceramic posts.
- Allow the kiln to cool for at least 45 minutes without lifting the kiln top.
- When opening the kiln after it has cooled, lay the kiln top upside-down on the heat-proof surface. Placing the top open-face down may cause heat to build up within the lid.
- Keep the hot kiln away from children and pets.